BIGTREETECH Octopus PRO V1.0/V1.1 Motherboard 32-Bit Control Board Upgrade Octopus TMC5160T TMC2208 VS Ender3 V2 Für CR10

Produktbeschreibung

【Main Control Chip】
The main control board uses 32-bit ARM-level Cortex-M4 series STM32H723ZE/ STM32F429ZE / STM32F446ZE chip with a frequency of up to 168MHz and the flash is 1MB.
【Support 60V Input】
Supports up to 8 3D printer motherboards with a maximum 60V stepper motor. The motor drive power supply supports up to 60V input (only for the motor drive power supply).
【6 Controllable Fans】
Up to 6 controllable fans, two normally open fans, and both support power supply voltage, 12V, 5V options.
【Update Firmware: Klipper/Marlin/RRF】
Supports firmware update via DFU mode. This is where the firmware is sent to the board directly from the PC and does not require a bootloader however this method is not recommended for novice users as discussed later in this document.
【Level conversion IC】
Supports proximity sensor, jumper optional pull-up resistor, supports more models, supports BL Touch.
Octopus Pro offers different versions of MCUs to meet the individual needs of DIY users.
ARM Cortex-M7 series, STM32H723ZET6, main frequency up to 550MHz, supports Marlin and Klipper, the best choice for Klipper high-speed printing. However, due to the limitation of 512kb flash, currently, RRF is not supported.
ARM Cortex-M4 series, STM32F429ZGT6, 180MHz main frequency, supports Marlin and Klipper, and with 1Mb flash, it can support RRF full function.
ARM Cortex-M4 series, STM32F446ZET6, 180MHz main frequency, supports Marlin and Klipper. However, due to the limitation of 512kb flash, it can only use the BTT custom version of RRF cutting off some functions.
Octopus Pro(F446) With TMC5160T PROx2 option: If you choose the shipping method of "Standard", the driver of TMC5160 Pro V1.1 version will be sent.
Octopus Pro
MINI 12864
Driver
1.Only the Octopus Pro Board
2.Octopus Pro Board + 2pcs TMC5160T Pro

Produktdetails in Bildern

Produkteigenschaften

Markenname

BIGTREETECH

Hochbetriebenes Chemikalienunternehmen

Keine

Ursprung

CN (Herkunft)

Artikeltyp

Mainplatine

Modellnummer

Octopus PRO V1.0/V1.1

Product Size

160*100mm

Mounting Size

150*90mm

Micro Processor

ARM 32-Bit Cortex-M4 CPU

Input Voltage

DC15-28V

Motor Driver

Pluggable Driver

Temperature Sensor Interface

TB T0 T1 T2 T3

Display

BIGTREETECH TFT LCD12864 LCD2004 etc

PC Communication Interface

Type-c easy to plug communication baud rate 115200

Expanded Interface

Broken material detection power failure power off BL Touch etc

Dile Format

G-code

Recommended Slicing Interface Software

Cura Simplify3D Pronterface Repetier-host Makerware

Cartridge Heater

4

Controllable Fan

6

Normally Open Fan

2

MCU

STM32F446ZET6 144Pin/STM32F429ZGT6 144Pin

Flash

512K/1M

SD Card Protocol

SDIO

WIFI Module Interface

Extension Special Interface

Supported Wifi Module

ESP8266 MAX500k/s

CANBus

CANBus With RJ11 Interface

Fuse

3

Limit Switch+Filament Sensor

6+2

HV Drive

MAX8

5V Short Circuit Alarm

YES,LED&Buzzer

Motor Input Voltage

12~60V,each one is optional

Drive Input Level

5V

Thermistor

NTC100K&PT100/PT1000

Supported Firmware

Klipper Marlin RRF

Supported Operating Systems

Raspberry Pi Octoprint

Mode

STEP DIR UART SPI

On-board MAX31865

YES

Type-C Interface

For Online Printing

Motor Input Voltage

60V

Motor Driver

8

Motherboard Protector

8

Frequency

180MHz/168MHz